The IPAS DALI Gateway DaliControl e64 Pro is a multi-master application controller for controlling electronic ballasts with DALI interface via the KNX installation bus. It supports ballasts according to EN 62386-102 ed1 (DALI1), devices according to EN 62386-102 ed2 (DALI2), as well as DALI2 motion sensors and light sensors according to EN 62386-303 and EN 62386-304.
The device transforms switching and dimming commands from the connected KNX system into corresponding DALI telegrams, or status and event information from the DALI bus into KNX telegrams.
The DaliControl e64 Pro has a DALI output which can control up to 64 ECGs. In addition, up to 8 DALI2 motion detectors or light sensors can be connected. Multi-master operation according to EN 62386-103 ed2 is permitted.
The required power supply for the connected ECGs and motion sensors is provided directly by the device. Additional DALI power supply is not required. When using sensors supplied via the DALI bus, it must be ensured that the current consumption of all connected DALI devices does not exceed the guaranteed value.
The device is available in a 4 DU wide DIN rail housing for direct installation in an electrical distribution board. The bus connection is made via a standard bus connector. Mains and DALI lines are connected via screw terminals on the device. Ethernet is connected via an RJ45 socket.
Per gateway the ECGs can be controlled in 16 groups. In addition to the group control the DaliControl e64 Pro also allows individual control of up to 64 ECGs.
As well as the control of all standard operating devices, the DaliControl e64 Pro enables the operation of single battery emergency lights (EN 62386-202) and supports emergency lighting systems with central battery.
A maximum of 8 motion detectors with light sensors can also be controlled.
The IPAS DALI Gateway DaliControl e64 Pro is a multi-master application controller for controlling electronic ballasts with DALI interface via the KNX installation bus. It supports ballasts according to EN 62386-102 ed1 (DALI1), devices according to EN 62386-102 ed2 (DALI2), as well as DALI2 motion sensors and light sensors according to EN 62386-303 and EN 62386-304.
The device transforms switching and dimming commands from the connected KNX system into corresponding DALI telegrams, or status and event information from the DALI bus into KNX telegrams.
The DaliControl e64 Pro has a DALI output which can control up to 64 ECGs. In addition, up to 8 DALI2 motion detectors or light sensors can be connected. Multi-master operation according to EN 62386-103 ed2 is permitted.
The required power supply for the connected ECGs and motion sensors is provided directly by the device. Additional DALI power supply is not required. When using sensors supplied via the DALI bus, it must be ensured that the current consumption of all connected DALI devices does not exceed the guaranteed value.
The device is available in a 4 DU wide DIN rail housing for direct installation in an electrical distribution board. The bus connection is made via a standard bus connector. Mains and DALI lines are connected via screw terminals on the device. Ethernet is connected via an RJ45 socket.
Per gateway the ECGs can be controlled in 16 groups. In addition to the group control the DaliControl e64 Pro also allows individual control of up to 64 ECGs.
As well as the control of all standard operating devices, the DaliControl e64 Pro enables the operation of single battery emergency lights (EN 62386-202) and supports emergency lighting systems with central battery.
A maximum of 8 motion detectors with light sensors can also be controlled.
The IPAS DALI Gateway DaliControl e64 Pro is a multi-master application controller for controlling electronic ballasts with DALI interface via the KNX installation bus. It supports ballasts according to EN 62386-102 ed1 (DALI1), devices according to EN 62386-102 ed2 (DALI2), as well as DALI2 motion sensors and light sensors according to EN 62386-303 and EN 62386-304.
The device transforms switching and dimming commands from the connected KNX system into corresponding DALI telegrams, or status and event information from the DALI bus into KNX telegrams.
The DaliControl e64 Pro has a DALI output which can control up to 64 ECGs. In addition, up to 8 DALI2 motion detectors or light sensors can be connected. Multi-master operation according to EN 62386-103 ed2 is permitted.
The required power supply for the connected ECGs and motion sensors is provided directly by the device. Additional DALI power supply is not required. When using sensors supplied via the DALI bus, it must be ensured that the current consumption of all connected DALI devices does not exceed the guaranteed value.
The device is available in a 4 DU wide DIN rail housing for direct installation in an electrical distribution board. The bus connection is made via a standard bus connector. Mains and DALI lines are connected via screw terminals on the device. Ethernet is connected via an RJ45 socket.
Per gateway the ECGs can be controlled in 16 groups. In addition to the group control the DaliControl e64 Pro also allows individual control of up to 64 ECGs.
As well as the control of all standard operating devices, the DaliControl e64 Pro enables the operation of single battery emergency lights (EN 62386-202) and supports emergency lighting systems with central battery.
A maximum of 8 motion detectors with light sensors can also be controlled.
Das IPAS DALI Gateway DaliControl e64 Pro ist ein Multi-Master Application-Controller zur Steuerung von elektronischen Vorschaltgeräten mit DALI Schnittstelle über den KNX Installationsbus. Unterstützt werden dabei Vorschaltgeräte sowohl gemäß EN 62386-102 ed1 (DALI-1), als auch Geräte gemäß EN 62386-102 ed2 (DALI-2), sowie DALI-2 Bewegungsmelder und Lichtsensoren gemäß EN 62386-303 und EN 62386-304.
Das Gerät wandelt Schalt- und Dimmbefehle vom angeschlossenen KNX System in entsprechende DALI Telegramme bzw. Status- und Ereignisinformationen vom DALI Bus in KNX Telegramme um.
Das DaliControl e64 Pro verfügt über einen DALI Ausgang über den 64 EVGs angesteuert werden können. Zusätzlich können bis zu 8 DALI-2 Bewegungsmelder oder Lichtsensoren angeschlossen werden. Ein Multi-Master Betrieb gemäß EN 62386-103 ed2 ist zulässig.
Die benötigte Stromversorgung für die angeschlossenen EVGs und Bewegungsmelder erfolgt direkt aus dem Gerät. Zusätzliche DALI Spannungsversorgungen sind nicht erforderlich. Bei Verwendung von Sensoren, die über den DALI Bus versorgt werden, ist zu berücksichtigen, dass die Stromaufnahme aller angeschlossener DALI Teilnehmer den garantierten Wert nicht übersteigt.
Das Gerät steht in einem 4 TE breiten Hutschienengehäuse zum direkten Einbau in einen Elektroverteiler zur Verfügung. Der Busanschluss erfolgt über eine Busklemme. Der Anschluss von Netz- und DALI-Leitungen erfolgen über Schraubklemmen am Gerät. Ethernet wird über eine RJ45-Buchse verbunden.
Pro Gateway können die EVGs in 16 Gruppen angesteuert werden. Zusätzlich zu der Gruppenansteuerung ist mit dem DaliControl e64 Pro auch eine Individualansteuerung der bis zu 64 EVGs möglich.
Neben der Ansteuerung von allen Standard-Betriebsgeräten erlaubt das DaliControl e64 Pro auch den Betrieb von Einzelbatterienotleuchten (EN 62386-202). Notleuchtensysteme mit Zentralbatterie werden ebenfalls unterstützt.
Max. 8 Bewegungsmelder mit Lichtsensoren können ebenfalls angesteuert werden.
Die spezielle Oberfläche zur Konfiguration der DALI Segmentes ist als DCA (Device Control App) für die ETS5 konzipiert. Es ist darauf zu achten, dass zusätzlich zur Produktdatenbank knxprod auch die entsprechende etsapp installiert wird. Diese steht bei der Konnex oder auf der IPAS Website zum Download zur Verfügung.
00 34 965 95 95 11
00 34 662 924 893
